Shenghui SH Needle Holder Series
product presentation
The board end connection parts are fixed to the circuit board and matched with the wire end rubber shell to complete the board and wire connection; the installation type (straight needle, curved needle or patch) is confirmed according to the board end layout and material number, and remains in the same series as the terminals and rubber shell. The specific model is subject to the latest selection table and drawings. Inside this type of equipment, the series corresponds the connection points of the plate end or wire end to the wire harness branches. During assembly, the material number is confirmed first, and then the crimping and docking directions are checked.
Structure and Supporting Facilities
From the wire end to the plate end, the components are crimp terminals, protective rubber shells and plate end needle seats in sequence. When docking, confirm the matching direction, locking form and wire exit position according to the material number to ensure consistent positioning.
- Wire-end terminal: crimped onto the end of the conductor wire; after being inserted into the plastic housing, it is positioned in conjunction with the mating connector or the board-end pin socket.
- Resin housing: encloses and secures the terminals, providing alignment guidance and a fail-safe design.
- Board end needle holder: fixed to the board end, wire end rubber shell insertion and docking (configured according to series)
- Component composition: Plate end needle holder is optional according to the same series of material numbers
Selection Parameters
When selecting a type, first check the purpose and spatial layout of the circuit, and then compare the component composition, coordination relationship and installation type. The number of bits, wire gauge and output direction are based on the drawings and bill of materials.
| Project | Explanation |
|---|---|
| Circuit applications and spatial layout | First, determine the internal connection points on the equipment and the routing of the wiring harness. |
| Component composition | Check the matching relationship between terminals, rubber shell and needle seat according to series |
| Number of digits and wire gauge | Verify against the part number and the drawing BOM; do not infer values based on general specifications. |
| Mounting type | The straight-pin, bent-pin, or surface-mount type of the plate-end pin socket shall be determined according to the part number. |
| Series positioning | For connecting plates and wires to similar equipment, the same series material number is preferred |
application scenarios
This series undertakes board-wire docking and wiring connection in the above scenarios, and the specific access location is determined according to the internal layout of the equipment.
- Fixed at the end of the circuit board to facilitate plug-and-play connectivity.
- Forms a wire-to-board connection in conjunction with the wire-end adhesive shell.
- Select between straight and bent needle types based on the layout of the board ends.
Part Number Composition and Purchase Verification
This page for Shenghui SH Needle Holder Series is used for series-level selection. After confirming the series and pitch, you still need to align each item including the specific part number, pin positions, installation type, and matching components before proceeding to request a quote or validate samples; the series page cannot replace the specific part number page.
| Verification Item | Specification on This Page |
|---|---|
| Series and Pitch | Shenghui SH Needle Holder Series, nominal pitch Confirm by part number; the exact part number should follow drawings or BOM |
| Component Composition | Terminal, housing, pin seat (for board-end applications may require additional parts; may include lock pieces depending on part number); select as a complete set from the same series |
| Installation Type | Through-hole or SMD, confirm according to series and part number |
| Pin Positions and Lead-Out Direction | Check according to part number, pin numbering, drawings, and BOM; do not infer based on generic pin positions |
| Crimping and Wire Gauge | Confirm according to terminal specification, conductor structure, and measured crimping range |
| Plating, Color, and Packaging | Confirm according to specific part number; series page does not replace part number page, specification, or sample |
| Substitution Boundary | Different series, different pin configurations, through-hole or surface-mount, with or without locks, that have the same spacing or similar appearance should not be interchanged based solely on appearance; terminals, housings, and sockets should be checked and matched as a complete set according to the same series part number. |
When requesting a quote, it is recommended to provide: target part number or compatible part number, number of pins, wire gauge and conductor structure, plating and color requirements, packaging method, estimated quantity, and delivery date. If any of these items are missing, first verify according to drawings or samples to avoid directly substituting with a similar series.
Quotation Request and Substitution
Quotations and supplies are based on material numbers, quantities, and delivery dates. Please prepare drawings or BOM for verification before docking. When it comes to alternative materials, it is necessary to confirm that the coordination relationship and circuit arrangement are consistent with the fixed type to avoid mixing similar series.
Related sections and similar materials:Classification of Shenghui SH connectors;Shenghui Brand Materials Column;Shenghui Home Appliance Connector Supporting Product Line;Shenghui Monitor Connector Series。