JST JC25 series 2.5 mm connector
Technical Specifications
Part Description JST JC25 series (per drawing / BOM)
Customer Part No. Per drawing / BOM
Drawing No. Per part number
Version Series overview
Date —

Dimensions

ItemValue
Pitch2.50 mm
ComponentsTerminal + Housing + Header
MountingThrough-hole (per series)

Product description

JST JC25 series is 2.50 mm pitch connector, used for wire harness docking and equipment internal interconnection, terminal crimping wire end and plastic shell, needle base with use. Series cover by material number docking, bit, wire gauge and lock form according to the drawing and selection table. In the wiring structure of wiring harness docking and internal interconnection of equipment, this series is used to correspond the connection point at the end of the board to the wiring harness branch.

Structure and form a complete set

From the line end to the plate end, the components are the crimping terminal, the protective rubber shell and the pin seat of the plate end in turn.

  • Wire Terminal: crimped on the end of the wire, into the plastic shell after the plate with the end of the needle base positioning
  • Rubber Shell: wraps and secures the terminals, providing docking guidance and foolproof construction
  • Needle Base: installed at the end of the plate, complete connection with the rubber shell
  • Coordination: terminals, plastic shell, needle base according to the same series of material selection

Parameters for type selection

When selecting the type, check the loop usage and space layout, and then check the spacing, component composition and installation type. The number and outlet direction are based on the drawing and Bill of material.

ProjectExplanation
Nominal spacing2.50mm
Componentsterminal, plastic shell and needle base
Installation typethrough hole installation (according to series and material number)
Digit and wire gaugecheck according to material number and drawing BOM, not according to general specification and so on
Series positioningfor wiring harness docking and equipment internal interconnection of the plate wire docking, priority check with series material number and line direction

Application scenarios

This series is responsible for board-line connection and wiring connection in structures such as wire harness connection and internal interconnection of equipment. The specific connection position is determined according to the internal layout of the equipment.

  • Butt joint of wire harness assembly
  • Internal interconnection of equipment
  • The end of the board is connected to the end of the wire

Part Number Composition and Purchase Verification

This page for JST JC25 series 2.5 mm connector is used for series-level selection. After confirming the series and pitch, you still need to align each item including the specific part number, pin positions, installation type, and matching components before proceeding to request a quote or validate samples; the series page cannot replace the specific part number page.

Verification ItemSpecification on This Page
Series and PitchJST JC25 series 2.5 mm connector, nominal pitch 2.50 mm; the exact part number should follow drawings or BOM
Component CompositionTerminal, housing, pin seat (for board-end applications may require additional parts; may include lock pieces depending on part number); select as a complete set from the same series
Installation TypeThrough-hole or SMD, confirm according to series and part number
Pin Positions and Lead-Out DirectionCheck according to part number, pin numbering, drawings, and BOM; do not infer based on generic pin positions
Crimping and Wire GaugeConfirm according to terminal specification, conductor structure, and measured crimping range
Plating, Color, and PackagingConfirm according to specific part number; series page does not replace part number page, specification, or sample
Substitution BoundaryDifferent series, different pin configurations, through-hole or surface-mount, with or without locks, that have the same spacing or similar appearance should not be interchanged based solely on appearance; terminals, housings, and sockets should be checked and matched as a complete set according to the same series part number.

When requesting a quote, it is recommended to provide: target part number or compatible part number, number of pins, wire gauge and conductor structure, plating and color requirements, packaging method, estimated quantity, and delivery date. If any of these items are missing, first verify according to drawings or samples to avoid directly substituting with a similar series.

Inquiry and substitution

Quotation and delivery are based on material number, quantity and delivery date. Please prepare drawing or BOM for checking before docking. When it comes to substitute materials, it is necessary to confirm the matching relationship and the outlet direction is the same as the fixed type, so as to avoid similar series mixed loading.

Related links: JST Series Connectors; JST Series Connectors Sourcing | PH·XH·SM·ZH·GH·VH Terminals & Housings; JST 5264 series 2.5 mm connector; JST DF11 series 2.0 mm connector

Get a Quote Back to List