Shenghui SH63 Series 3P/4P wire-to-wire connectors
product presentation
3P/4P multi-circuit small wiring configuration, with the wire end crimping terminals installed in the corresponding rubber shell, and multiple sets of wires are docked side by side in the same rubber shell. It is often used for group signal connection between internal modules and functional boards of home appliances; the number of circuits and the output direction are checked according to the drawings. Inside this type of equipment, the series corresponds the connection points of the plate end or wire end to the wire harness branches. During assembly, the material number is confirmed first, and then the crimping and docking directions are checked.
Structure and Supporting Facilities
This series consists of wire end crimping terminals and corresponding rubber shells. Needle holders are also provided for the plate end. Each component is selected according to the same series material number. Before assembly, check the wire crimping direction, rubber shell positioning and locking position.
- Wire-end terminal: crimped onto the end of the conductor wire; after being inserted into the plastic housing, it is positioned in conjunction with the mating connector or the board-end pin socket.
- Resin housing: encloses and secures the terminals, providing alignment guidance and a fail-safe design.
- Board end needle holder: fixed to the board end, wire end rubber shell insertion and docking (configured according to series)
- Component composition: Terminals and rubber shells are optional according to the same series of material numbers
Selection Parameters
When selecting a type, first check the purpose and spatial layout of the circuit, and then compare the component composition, coordination relationship and installation type. The number of bits, wire gauge and output direction are based on the drawings and bill of materials.
| Project | Explanation |
|---|---|
| Circuit applications and spatial layout | First, determine the internal connection points on the equipment and the routing of the wiring harness. |
| Component composition | Check the matching relationship between terminals, rubber shell and needle seat according to series |
| Number of digits and wire gauge | Verify against the part number and the drawing BOM; do not infer values based on general specifications. |
| Mounting type | The straight-pin, bent-pin, or surface-mount type of the plate-end pin socket shall be determined according to the part number. |
| Series positioning | For connecting plates and wires to similar equipment, the same series material number is preferred |
application scenarios
This series undertakes board-wire docking and wiring connection in the above scenarios, and the specific access location is determined according to the internal layout of the equipment.
- Interconnection of multiple circuit modules within household appliances
- The connection between the functional board and the wiring harness branch
- Internal grouped signal wiring in small equipment
Part Number Composition and Purchase Verification
This page for Shenghui SH63 Series 3P/4P wire-to-wire connectors is used for series-level selection. After confirming the series and pitch, you still need to align each item including the specific part number, pin positions, installation type, and matching components before proceeding to request a quote or validate samples; the series page cannot replace the specific part number page.
| Verification Item | Specification on This Page |
|---|---|
| Series and Pitch | Shenghui SH63 Series 3P/4P wire-to-wire connectors, nominal pitch Confirm by part number; the exact part number should follow drawings or BOM |
| Component Composition | Terminal, housing, pin seat (for board-end applications may require additional parts; may include lock pieces depending on part number); select as a complete set from the same series |
| Installation Type | Through-hole or SMD, confirm according to series and part number |
| Pin Positions and Lead-Out Direction | Check according to part number, pin numbering, drawings, and BOM; do not infer based on generic pin positions |
| Crimping and Wire Gauge | Confirm according to terminal specification, conductor structure, and measured crimping range |
| Plating, Color, and Packaging | Confirm according to specific part number; series page does not replace part number page, specification, or sample |
| Substitution Boundary | Different series, different pin configurations, through-hole or surface-mount, with or without locks, that have the same spacing or similar appearance should not be interchanged based solely on appearance; terminals, housings, and sockets should be checked and matched as a complete set according to the same series part number. |
When requesting a quote, it is recommended to provide: target part number or compatible part number, number of pins, wire gauge and conductor structure, plating and color requirements, packaging method, estimated quantity, and delivery date. If any of these items are missing, first verify according to drawings or samples to avoid directly substituting with a similar series.
Quotation Request and Substitution
Drawings, BOMs, or samples can be provided for material number verification; prices are based on material number, quantity, and delivery date. The replacement materials need to be confirmed item by item according to the series structure, matching components and installation type, and will not be directly mixed across series.
Related sections and similar materials:Classification of Shenghui SH connectors;Shenghui Brand Materials Column;Shenghui SH42003 series multi-pole wire-to-wire connectors;Shenghui SH25011 series 2–15P pin-to-pin connectors。