JST SH series 1.0mm connector
Product description
The JST SH series is a 1.00 mm pitch connector designed for high-density, miniaturized wiring connections inside devices, typically including camera modules and portable devices. The component is composed of terminal, rubber shell and needle base. The SMT and through hole installation type are distinguished by series and material number. The matching relationship is based on the drawing. In the wiring structure of high-density small equipment, camera and portable equipment, this series is used to correspond the connection point at the end of the board to the wiring harness branch.
Structure and form a complete set
From the line end to the plate end, the components are the crimping terminal, the protective rubber shell and the pin seat of the plate end in turn.
- Wire Terminal: crimped on the end of the wire, into the plastic shell after the plate with the end of the needle base positioning
- Rubber Shell: wraps and secures the terminals, providing docking guidance and foolproof construction
- Needle Base: installed at the end of the plate, complete connection with the rubber shell
- Coordination: terminals, plastic shell, needle base according to the same series of material selection
Parameters for type selection
When selecting the type, check the loop usage and space layout, and then check the spacing, component composition and installation type. The number and outlet direction are based on the drawing and Bill of material.
| Project | Explanation |
|---|---|
| Nominal spacing | 1.00mm |
| Components | terminal, plastic shell and needle base |
| Mounting type | patch and through-hole mounting type (by series and material number) |
| Digit and wire gauge | check according to material number and drawing BOM, not according to general specification and so on |
| Series positioning | for high-density small devices, cameras and portable devices of the board line docking, priority check with the series of material number and line direction |
Application scenarios
This series is responsible for board-line connection and wiring connection in high-density small devices, cameras and portable devices, etc. The specific connection position is determined according to the internal layout of the device.
- Internal connection of the camera module
- High density wiring for portable equipment
- Signal connection between miniature boards
Part Number Composition and Purchase Verification
This page for JST SH series 1.0mm connector is used for series-level selection. After confirming the series and pitch, you still need to align each item including the specific part number, pin positions, installation type, and matching components before proceeding to request a quote or validate samples; the series page cannot replace the specific part number page.
| Verification Item | Specification on This Page |
|---|---|
| Series and Pitch | JST SH series 1.0mm connector, nominal pitch 1.00 mm; the exact part number should follow drawings or BOM |
| Component Composition | Terminal, housing, pin seat (for board-end applications may require additional parts; may include lock pieces depending on part number); select as a complete set from the same series |
| Installation Type | Through-hole or SMD, confirm according to series and part number |
| Pin Positions and Lead-Out Direction | Check according to part number, pin numbering, drawings, and BOM; do not infer based on generic pin positions |
| Crimping and Wire Gauge | Confirm according to terminal specification, conductor structure, and measured crimping range |
| Plating, Color, and Packaging | Confirm according to specific part number; series page does not replace part number page, specification, or sample |
| Substitution Boundary | Different series, different pin configurations, through-hole or surface-mount, with or without locks, that have the same spacing or similar appearance should not be interchanged based solely on appearance; terminals, housings, and sockets should be checked and matched as a complete set according to the same series part number. |
When requesting a quote, it is recommended to provide: target part number or compatible part number, number of pins, wire gauge and conductor structure, plating and color requirements, packaging method, estimated quantity, and delivery date. If any of these items are missing, first verify according to drawings or samples to avoid directly substituting with a similar series.
Inquiry and substitution
Quotation and delivery are based on material number, quantity and delivery date. Please prepare drawing or BOM for checking before docking. When it comes to substitute materials, it is necessary to confirm the matching relationship and the outlet direction is the same as the fixed type, so as to avoid similar series mixed loading.
Related links: JST Series Connectors; JST Series Connectors Sourcing | PH·XH·SM·ZH·GH·VH Terminals & Housings; JST GH series 1.25 mm connector; JST E H series 2.5 mm connector