JST XH series 2.5 mm connector
Product description
JST XH series is 2.50 mm pitch connector, commonly used in power and signal circuit, battery pack and lighting wiring and other scenarios, wire terminal terminal and back docking plate pin holder. The same series can be seen XHS, XHD, XHB and other derived types, all belong to the scope of the series overview, the specific model to the drawings and BOM check shall prevail. In the wiring structure of power signal connection, battery and lighting wiring, this series is used to correspond the connection point at the end of the board to the wiring harness branch.
Structure and form a complete set
From the line end to the plate end, the components are the crimping terminal, the protective rubber shell and the pin seat of the plate end in turn.
- Wire Terminal: crimped on the end of the wire, into the plastic shell after the plate with the end of the needle base positioning
- Rubber Shell: wraps and secures the terminals, providing docking guidance and foolproof construction
- Needle Base: installed at the end of the plate, complete connection with the rubber shell
- Coordination: terminals, plastic shell, needle base according to the same series of material selection
Parameters for type selection
When selecting the type, check the loop usage and space layout, and then check the spacing, component composition and installation type. The number and outlet direction are based on the drawing and Bill of material.
| Project | Explanation |
|---|---|
| Nominal spacing | 2.50mm |
| Components | terminal, plastic shell and needle base |
| Installation type | through hole installation (according to series and material number) |
| Digit and wire gauge | check according to material number and drawing BOM, not according to general specification and so on |
| Series positioning | for power supply signal connection, battery and lighting wiring board wire docking, priority check with series material number and direction |
Application scenarios
This series is responsible for board-line connection and wiring connection in structures such as power signal connection, battery and lighting wiring, etc. The specific connection position is determined according to the internal layout of the equipment.
- Power supply and signal wiring for equipment
- Internal connection of battery pack
- Wiring of lighting circuit
Part Number Composition and Purchase Verification
This page for JST XH series 2.5 mm connector is used for series-level selection. After confirming the series and pitch, you still need to align each item including the specific part number, pin positions, installation type, and matching components before proceeding to request a quote or validate samples; the series page cannot replace the specific part number page.
| Verification Item | Specification on This Page |
|---|---|
| Series and Pitch | JST XH series 2.5 mm connector, nominal pitch 2.50 mm; the exact part number should follow drawings or BOM |
| Component Composition | Terminal, housing, pin seat (for board-end applications may require additional parts; may include lock pieces depending on part number); select as a complete set from the same series |
| Installation Type | Through-hole or SMD, confirm according to series and part number |
| Pin Positions and Lead-Out Direction | Check according to part number, pin numbering, drawings, and BOM; do not infer based on generic pin positions |
| Crimping and Wire Gauge | Confirm according to terminal specification, conductor structure, and measured crimping range |
| Plating, Color, and Packaging | Confirm according to specific part number; series page does not replace part number page, specification, or sample |
| Substitution Boundary | Different series, different pin configurations, through-hole or surface-mount, with or without locks, that have the same spacing or similar appearance should not be interchanged based solely on appearance; terminals, housings, and sockets should be checked and matched as a complete set according to the same series part number. |
When requesting a quote, it is recommended to provide: target part number or compatible part number, number of pins, wire gauge and conductor structure, plating and color requirements, packaging method, estimated quantity, and delivery date. If any of these items are missing, first verify according to drawings or samples to avoid directly substituting with a similar series.
Inquiry and substitution
Quotation and delivery are based on material number, quantity and delivery date. Please prepare drawing or BOM for checking before docking. When it comes to substitute materials, it is necessary to confirm the matching relationship and the outlet direction is the same as the fixed type, so as to avoid similar series mixed loading.
Related links: JST Series Connectors; JST Series Connectors Sourcing | PH·XH·SM·ZH·GH·VH Terminals & Housings; JST SM series 2.5mm connector; JST ZH series 1.5 mm connector