JST ZH series 1.5 mm connector
Product description
The JST ZH series are 1.50 mm pitch connectors for compact small precision equipment connected to sensor signals. The terminals are crimped to the wire end and then mounted in a rubber case, which is used in conjunction with the plate end needle base. When selecting the type, check the number of bits, wire gauge and installation type according to the drawing, not replaced by the general specification. In the wiring structure of small precision equipment and sensors, this series is used to correspond the connection point at the end of the board to the wiring harness branch.
Structure and form a complete set
The terminal is located at the end of the wire, the rubber shell is responsible for positioning and foolproof, and the needle base is fixed at the end of the plate. The relationship between the three is based on the series selection.
- Wire Terminal: crimped on the end of the wire, into the plastic shell after the plate with the end of the needle base positioning
- Rubber Shell: wraps and secures the terminals, providing docking guidance and foolproof construction
- Needle Base: installed at the end of the plate, complete connection with the rubber shell
- Coordination: terminals, plastic shell, needle base according to the same series of material selection
Parameters for type selection
When selecting the type, check the loop usage and space layout, and then check the spacing, component composition and installation type. The number and outlet direction are based on the drawing and Bill of material.
| Project | Explanation |
|---|---|
| Nominal spacing | 1.50mm |
| Components | terminal, plastic shell and needle base |
| Mounting type | through hole and Smt mounting type (according to series and material number) |
| Digit and wire gauge | check according to material number and drawing BOM, not according to general specification and so on |
| Series positioning | for small precision equipment and sensor wire butt, priority to check the same series material number and direction of the wire |
Application scenarios
This series is responsible for board wire connection and wiring connection in small precision equipment and sensors and other structures. The specific connection position is determined according to the internal layout of the equipment.
- Internal signal wiring for precision equipment
- Sensor signal acquisition connection
- Plate and wire butt joint of compact layout
Part Number Composition and Purchase Verification
This page for JST ZH series 1.5 mm connector is used for series-level selection. After confirming the series and pitch, you still need to align each item including the specific part number, pin positions, installation type, and matching components before proceeding to request a quote or validate samples; the series page cannot replace the specific part number page.
| Verification Item | Specification on This Page |
|---|---|
| Series and Pitch | JST ZH series 1.5 mm connector, nominal pitch 1.50 mm; the exact part number should follow drawings or BOM |
| Component Composition | Terminal, housing, pin seat (for board-end applications may require additional parts; may include lock pieces depending on part number); select as a complete set from the same series |
| Installation Type | Through-hole or SMD, confirm according to series and part number |
| Pin Positions and Lead-Out Direction | Check according to part number, pin numbering, drawings, and BOM; do not infer based on generic pin positions |
| Crimping and Wire Gauge | Confirm according to terminal specification, conductor structure, and measured crimping range |
| Plating, Color, and Packaging | Confirm according to specific part number; series page does not replace part number page, specification, or sample |
| Substitution Boundary | Different series, different pin configurations, through-hole or surface-mount, with or without locks, that have the same spacing or similar appearance should not be interchanged based solely on appearance; terminals, housings, and sockets should be checked and matched as a complete set according to the same series part number. |
When requesting a quote, it is recommended to provide: target part number or compatible part number, number of pins, wire gauge and conductor structure, plating and color requirements, packaging method, estimated quantity, and delivery date. If any of these items are missing, first verify according to drawings or samples to avoid directly substituting with a similar series.
Inquiry and substitution
During the type selection and confirmation stage, drawings or bill of material can be submitted to check the configuration. If an alternative type is required, the spacing, component composition and plate end installation method should be checked before use.
Related links: JST Series Connectors; JST Series Connectors Sourcing | PH·XH·SM·ZH·GH·VH Terminals & Housings; JST SH series 1.0mm connector; JST GH series 1.25 mm connector